-
1 допустимый длительный ток кабеля (провода)
допустимый длительный ток кабеля (провода)
-
[Интент]
допустимый длительный ток (проводника)
Максимальный электрический ток, который проводник способен проводить в продолжительном режиме без превышения его установившейся температурой определённого значения.
Допустимый длительный ток является одной из основных характеристик проводника. Он представляет собой максимальный электрический ток, который проводник может проводить длительно (неделями, месяцами, годами) не перегреваясь. Значение допустимого длительного тока зависит от сечения проводника, материалов из которых выполнены проводник и его изоляция, способов монтажа проводника в электроустановке здания. Допустимый длительный ток проводника фактически является его номинальным током. В электроустановках зданий выполняют защиту проводников от сверхтоков, протекание которых по проводникам сопровождается их перегревом.
[ http://www.volt-m.ru/glossary/letter/%C4/view/11/]EN
current carrying capacity
maximum current a cable circuit (one or several conductors) can support resulting in a specified increase of the surface temperature of the conductor beyond the ambient temperature, not exceeding the maximum allowed operating temperature of the cable
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]FR
courant maximal admissible
courant maximal qu’un circuit de câble (un ou plusieurs conducteurs) peut supporter avec une augmentation spécifiée de la température de surface du conducteur au delà de la température ambiante, et ne dépassant pas la température maximale de fonctionnement autorisée du câble
[IEC 61156-1, ed. 3.0 (2007-06< size="2">)]Номинальный ток устройств защиты от короткого замыкания может превышать допустимый длительный ток кабеля.
[ ГОСТ Р 50571. 5-94 ( МЭК 364-4-43-77)]Допустимые длительные токи для проводов и кабелей, проложенных в коробах, а также в лотках пучками, должны приниматься...
[ПУЭ]Тематики
- кабели, провода...
- электроустановки
EN
- ampere capacity
- current carrying capacity
- current carrying capacity of the cable
- current carrying capacity of the conductors
- current-carrying capacity of the cable
FR
Русско-французский словарь нормативно-технической терминологии > допустимый длительный ток кабеля (провода)
-
2 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
3 максимальная допустимая температура
максимальная допустимая температура
-
[IEV number 442-06-41]EN
maximum permissible temperature
maximum service temperature
Denotes the highest temperature which the connecting device is allowed to attain in normal use as a result of ambient temperature, induced heat, and heat caused by the device itself
[IEV number 442-06-41]FR
température maximale permise
température maximale de service
Température la plus élevée que le dispositif de connexion peut atteindre en usage normal et résultant de la température ambiante, de la chaleur induite et de la chaleur dégagée par le dispositif lui-même
[IEV number 442-06-41]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > максимальная допустимая температура
-
4 максимально допустимая концентрация
максимально допустимая концентрация
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
maximum admissible concentration
The maximum exposure to a physical or chemical agent allowed in an 8-hour work day to prevent disease or injury. (Source: KOREN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > максимально допустимая концентрация
См. также в других словарях:
maximum allowed zero-fuel weight — The maximum authorized weight of an aircraft without taking into account the weight of the fuel … Aviation dictionary
Maximum throughput scheduling — is a procedure for scheduling data packets in a packet switched best effort communications network, typically a wireless network, in view to maximize the total throughput of the network, or the system spectral efficiency in a wireless network.… … Wikipedia
maximum — ▪ I. maximum max‧i‧mum 1 [ˈmæksməm] adjective [only before a noun] the maximum amount, quantity etc is the largest that is possible or allowed: • The maximum cost of the plan would be $9.7 million. • The maximum rate of income tax was cut to 35… … Financial and business terms
Maximum Takeoff Weight — The Maximum Takeoff Weight (MTOW) or Maximum Takeoff Mass of an aircraft is the maximum weight at which the pilot of the aircraft is allowed to attempt to take off, due to structural or other limits. The analogous term for rockets is Gross Lift… … Wikipedia
Maximum daily delivery limit — The maximum daily delivery amount is a maximum amount of money that is allowed to be delivered to a given party. Maximum allowed delivery risk, expressed in local currency … International financial encyclopaedia
Maximum Take Off Weight — Das Höchstabfluggewicht (engl. maximum take off weight, MTOW) ist das maximale Startgewicht eines Flugzeugs. Dies ist das Gewicht, mit dem das Flugzeug abheben kann, ohne die vorgeschriebenen Sicherheitsreserven zu verletzen. Das maximale… … Deutsch Wikipedia
Maximum Ride: School's Out Forever — Maximum Ride: School s Out Forever … Wikipedia
Maximum Fighting Championship — Type Private Industry Mixed martial arts promotion Founded 2001 Founder(s) … Wikipedia
Maximum Contaminant Level — Maximum Contaminant Levels (MCLs) are standards that are set by the United States Environmental Protection Agency (EPA) for drinking water quality. An MCL is the legal threshold limit on the amount of a substance that is allowed in public water… … Wikipedia
Maximum time in grade — in a military force is the longest amount of time that an officer or enlisted man is allowed to remain in the service without being promoted. If the soldier has not been promoted by the time he reaches MTIG, he is discharged from the service. In… … Wikipedia
Maximum wage — A maximum wage, also often called a wage ceiling, is a legal limit on how much income an individual can earn.[1] This is a related economic concept that is complementary to the minimum wage used currently by some states to enforce minimum… … Wikipedia
